Freematics OBD-II 에뮬레이터 MK1
(Freematics OBD-II Emulator MK1)
개요
- 본 제품은 차량의 OBD-II 포트를 에뮬레이션하여 주는 12x8x3cm의 작은 크기의 에뮬레이터입니다.
- 표준 16핀 female OBD-II 포트와 9개의 노브, 3개의 스위치, USB 포트, 12 VDC 전원 포트 및 전원 버튼을 가지고 있는 제품입니다.
- OBD-II 포트는 실제 자동차의 OBD 포트와 동일하며, 실제 자동차의 OBD-II 포트처럼 동작합니다.
- OBD 어플리케이션을 개발할때 본 에뮬레이터를 사용하면 실제 차량없이 빠르게 개발이 가능합니다.
- OBD-II PID 변경하거나 DTC(Diagnostic Trouble Codes)를 설정하거나, VIN(Vehicle Identification Number) 등을 설정하려면 Freematics OBD-II Emulator MK2를 고려하여 보십시오.
특징
- Emulating OBD-II port identical to one in a real car
- Responding to standard OBD-II PIDs polls and VIN request
- Switching among supported vehicle data bus by physical switches and USB serial terminal
- Value of PIDs controllable by physical knobs
- Providing both power and data for OBD-II compliant devices
- Following protocols are supported:
- CAN 500Kbps/11bit
- CAN 250Kbps/11bit
- CAN 500Kbps/29bit
- CAN 250Kbps/29bit
- ISO9141-2
- KWP2000 Fast
- KWP2000 5Kbps
- By default following OBD-II PIDs can be controlled through the 9 knobs:
- 0104 - Calculated engine load value
- 010C - Engine RPM
- 010D - Vehicle speed
- 0110 - MAF air flow rate
- 0111 - Throttle position
- 012F - Fuel level input
- 010A - Fuel pressure
- 010B - Intake manifold absolute pressure
- 015E - Engine fuel rate
- Besides above OBD-II PIDs, other standard OBD-II PIDs are also accessible with a fixed value. The value of PID 011F (Run time since engine start) changes along with real time. VIN is also accessible.
- To change additional OBD-II PIDs, or set DTC (Diagnostic Trouble Codes) and VIN (Vehicle Identification Number), check out the Freematics OBD-II Emulator MK2.
- Configuration
- Freematics OBD-II emulator can be configured by the 3 switches or USB serial command line interface.
-
The baudrate of CAN bus protocol simulation can be configured by the 250K/500K switch. The CAN ID switch can toggle between 29-bit and 11-bit CAN ID. The type of KWP2000 protocol (ISO9141-2 or ISO14230) can be altered by the thrid switch.
The simulated protocol can also be altered via the serial command line interface. To do this, connect the emulator to a computer with a USB cable, open serial interface (with any serial terminal program) with baudrate of 115200bps, and then enter one of the following commands followed by character 0x0D (\r).
- CAN_11B_500K
- CAN_29B_500K
- CAN_11B_250K
- CAN_29B_250K
- KWP2000_FAST
- KWP2000_5BPS
- ISO9141_2
문서
- n/a
연관제품
- 연관제품 1