LARA-R6 LTE 이동통신 모듈 -LTE Cat 1
(SparkFun LTE Stick - LARA-R6)
개요
- 본 제품은 LARA-R6 LTE 이동통신 모듈 -LARA-R6401입니다.
- ublox사의 LARA-R6 LTE Cat 1 모듈( LARA-R6401) 을 탑재하고 있습니다.
- 여러 LTE FDD 주파수 밴드(2, 4, 5, 12, 13, 14, 66, 71) 에서 동작하며 UART 및 I2S 인터페이스를 가지고 있습니다.
- 두개의 SMA 커넥터가 있어 주 안테나와 보조 안테나 연결을 할 수 있습니다. 주안테나는데이터를 송수신 가능하며, 보조 안테나는 수신만 가능합니다.
- 전원 공급은 USB C 커넥터를 통해 이루어 집니다.
특징
- LARA-R6401 LTE Cellular Module
- Region: North America
- LTE FDD Bands: 2, 4, 5, 12, 13, 14, 66, & 71
- 2x UART
- USB 2.0
- I2C
- 9 GPIO
- Digital Audio (I2S)
- Nano SIM Card Slot
- Power On & Reset Buttons
- USB-C Connector
- PTH Connections
- UART
- I2S
- Reset
- Power On
- Power (VIN, 3.3V, & 1.8V)
- Test Point Cluster Connections (Not Level Shifted. 1.8V Only)
- GPIO (1, 2, 3 & 6)
- UART2
- I2C
- 2x SMA Antenna Connectors
- Primary Antenna: Transmit & Receive
- Secondary Antenna: Receive Only
-
The SparkFun LTE Stick provides a development and prototyping platform for the LARA-R6 LTE Cat 1 module from u-blox™. The LTE Stick uses the LARA-R6401 version, which supports both data and voice for North America and works with LTE bands used by these mobile networks: AT&T, Verizon, T-Mobile, and FirstNet. The board includes a nanoSIM card slot for users to select their preferred network. Check with your network provider for compatibility with the LARA-R6.
The LARA-R6 works on multiple LTE FDD frequency bands (2, 4, 5, 12, 13, 14, 66, and 71) and includes a host of common features users expect from u-blox modules, including uFOTA (over-the-air firmware update), Root of Trust, secure boot/update, jamming detection, antenna and SIM detection, and much more.
The LTE Stick routes the UART and I2S interfaces to a 0.1in.-spaced plated-through-hole (PTH) header along with the Reset and Power On signals, and we designed the board to mount onto a breadboard specifically for easy prototyping. Since the LARA-R6401 supports data and voice, you can use the LTE Stick with the right parts (such as an audio codec, microphone, speaker, & microcontroller) and code; you can make your own breadboard telephone!
The board has two SMA connectors for the LARA-R6's primary and secondary antennas. The primary antenna sends and receives data, whereas the secondary antenna is receive only. Power to the board is provided either over the USB-C connector (recommended) or the VIN PTH pin (6V Max). The board defaults to use the higher voltage input. Lastly, the board also includes test points for advanced users to solder to for the I2C interface, secondary UART, and four GPIO pins (IO1, IO2, IO3, and IO6).