아두이노 MKR VIDOR 4000 보드 -10CL016 FPGA
(ARDUINO MKR VIDOR 4000)
개요
- 본 제품은 정품 아두이노 MKR VIDOR 4000 보드입니다.
- 인텔 사이클론 10CL016 FPGA를 탑재한 제품으로 고속 디지털 오디오 및 비디오 프로세싱이 가능한 아두이노 보드입니다.
- 8MB SRAM, 2MB QSPI 플래쉬, 마이크로 HDMI 커넥터, MIPI 카메라 커넥터, WiFi/BLE U-BLOX NINA W10 를 탑재하고 있습니다.
- 25개의 사용자 프로그래밍이 가능한 핀을 가진 미니 PCI Express 커넥터를 장착하고 있습니다.
- MCU는 SAMD21 을 장착하과 있으며, FPGA칩과 SAMD21 MCU간에는 끊김 없는 통신을 지원합니다.
특징
-
FPGA Intel Cyclone 10CL016 Mini PCI Express port with programmable pins Camera connector MIPI camera connector Circuit Operating Voltage 3.3V Digital I/O Pins 22 headers + 25 Mini PCI Express PWM Pins All Pins UART Up to 7 (depends on FPGA configuration) SPI Up to 7 (depends on FPGA configuration) I2C Up to 7 (depends on FPGA configuration) Analog Input Pins n/a Analog Output Pins n/a External Interrupts n/a DC Current per I/O Pin 4 or 8 mA Flash Memory 2 MB SDRAM 8 MB EEPROM n/a Clock Speed 48 MHz - up to 200 MHz Video Output Micro HDMI Microcontroller Microchip ATSAMD21 (Arm Cortex-M0+ processor) Wi-Fi U-blox Nina-W102 (VIN) 5V Supported Battery(*) Li-Po Single Cell, 3.7V, 700mAh Minimum Circuit Operating Voltage 3.3V Digital I/O Pins 22 PWM Pins 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19) UART 1 SPI 1 I2C 1 Analog Input Pins 7 (ADC 8/10/12 bit) Analog Output Pins 1 (DAC 10 bit) External Interrupts 8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17) Flash Memory 256 KB SRAM 32 KB EEPROM No Clock Speed 32.768 kHz (RTC), 48 MHz LED_BUILTIN 6 Full-Speed USB Device and Embedded Host Included LED_BUILTIN 6 Length 83 mm Width 25 mm Weight 32 g
문서
-
OSH: Schematics
The MKR Vidor 4000 is open-source hardware! You can build your own board using the following files:
Additional I2C Port
The MKR Vidor 4000 has an additional connector meant as an extension of the I2C bus. It's a small form factor 5-pin connector with 1.0mm pitch. The mechanical details of the connector can be found in the connector datasheet. The I2C port in addition to the SDA and SCL signals includes the GND and +5V power rails and a digital pin that might be useful when designing an expansion. The pinout is shown in the following image:
The connector we suggest for this additional I2C Port is the SHR-05V-S-B, also in the picture.