nRF9160 스파크펀 IoT 띵 플러스 보드 -LTE, NB-IoT
(SparkFun Thing Plus - nRF9160)
개요
- 본 제품은 nRF9160 스파크펀 IoT 띵 플러스 보드 입니다.
- nRF9160 MCU를 탑재한 Feather 보드 폼팩터를 가진 제품입니다.
- nRF9160 칩은 LTE 및 NB-IoT 이동통신을 둘다 지원하며, 임베디드 시스템 개발을 위해 Zephyr, go-to RTOS와 동작할 수 있게 디자인되었습니다.
- 4MB의 외부 플래쉬 메모리를 지원합니다.
특징
- Nordic nRF9160 Microcontroller with ARM Cortex M33
- 1MB Flash
- 256kB RAM
- ARM® TrustZone®
- ARM® Cryptocell 310
- Up to 4x SPI, I2C and UART with Easy DMA
- I2S w/ EasyDMA
- 4x PWM with EasyDMA
- 12bit SADC with EasyDMA
- 2x RTC
- PPI (Programmable peripheral interconnect) interface
- Radio
- Transceiver and baseband
- 3GPP LTE release 13 Category M1 and NB1 compliant
- 3GPP release 14 NB2 compliant
- GPS receiver (GPS L1 C/A supported) - Active antenna only.
- RF Transceiver for global coverage supporting bands:
- Cat-M1: B1, B2, B3, B4, B5, B8, B12, B13, B14, B17, B18, B19, B20, B25, B26, B28, B66
- Cat-NB1/NB2: B1, B2, B3, B4, B5, B8, B12, B13, B17, B18, B20, B25, B26, B28, B66
- Supports 4FF Nano SIM
- USB-C connection for USB-to-Serial and DFU
- Pre-programmed MCUBoot bootloader
- External NOR Flash by Winbond
- 4MB of space
- Max bus speed of 133MHz
- Standard SPI
- Power supply
- 3.3V Buck/Boost up to 0.9A of current draw
- Operating range 2.8 to 5.5V
- External LiPoly battery connection (JST SPH type)
- Charge rate set to 300mA with LED indication
- Programmer
- Capable of interfacing with J-Link and CMSIS-DAP based programmers
- Low Power RTC on board for time keeping and as a low power wakeup source.
- User I/O
- Standard feather form factor GPIOs (0.1" pitch)
- 2x buttons (1 Reset, 1 General Purpose)
- 1x Blue LED connected to D7
- Antenna connections:
- 1x U.FL for LTE with matching network
- 1x U.FL for active GPS antennas
- Feather form factor
- 58.42mm x 22.86mm (2.3" x 0.9")
-
Not only can you take advantage of Nordic's advanced power states, but you can also put the device into a low power standby state. Laboratory measurements are putting that mode at about 2µA of current. 2µA! It also features a 3.3V Buck-Boost which helps get every mWh from your batteries as possible.
No batteries? No problem! Power your nRF9160 Thing Plus externally with a USB-C cable. Keep it on at all times for high availability scenarios.
Want to persist data? The nRF9160 Thing Plus has a 4MB external flash for storing data while offline. Using external flash with a filesystem like LitteFS and you'll have a project to recon with!