MAX41470 RF 리시버 모듈 - Sub-1Ghz
(ISM RX 3 CLICK)
개요
- 본 제품은 MAX41470 RF 리시버 모듈 - Sub-1Ghz 입니다.
- MAX41470 칩을 기반으로 디자인된 제품으로 고성능 저전력 리시버입니다.
- 세개의 sub-1Ghz 밴드(287MHz to 320MHz, 425MHz to 480MHz, 860MHz to 960MHz)로 설정하여 사용이 가능합니다.
- SPI 인터페이스를 가지고 있으며, 3.3V 시스템과 사용이 가능합니다.
특징
-
HOW DOES IT WORK?
ISM RX 3 Click as its foundation uses the MAX41470, a sub-GHz ISM RF receiver from Analog Devices. This IC is designed to receive ASK/OOK or FSK/GFSK modulated data in the 287MHz to 320MHz (nominally 315MHz), 425MHz to 480MHz (nominally 434MHz), and 860MHz to 960MHz (nominally 868MHz or 915MHz) ISM frequency bands, using an onboard 16MHz crystal. This Click board™ comes with an ASK modulation and 433.92MHz with a 5bps data rate as its default configuration. Its additional features also include automatic gain control (AGC), a received signal strength indicator (RSSI), automatic frequency control (AFC), and a frequency error indicator (FEI).
The MAX41470 has four power states: Shutdown, Sleep, Standby, and Receive-Active. Its Power-Down pin, labeled as PDN and routed to the RST pin of the mikroBUS™ socket, optimizes power consumption used for power ON/OFF purposes. When the device is enabled (the PDN pin set to a low logic state), the device operational states are controlled through the serial interface by the internal registers.
This Click board™ communicates with MCU through a standard SPI interface that enables very high clock speeds up to 20MHz, supporting the most common SPI mode, SPI Mode 3 to program the internal registers for complete control of the MAX41470. When in programming mode, the MAX41470 can support a self-polling operation to provide an interrupt signal on the DAT pin routed to the AN pin of the mikroBUS™ socket.
The MAX41470 comes only with one data pin for register programming, both data input/output pin. For that purpose, this Click board™ uses the 74LVC1G3157 multiplexer to avoid conflict with other functions driven by the same pin, enabling both writing and reading via the SPI interface and using the 4-wire SPI interface. The selection of the multiplexer channel, more precisely the MISO or MOSI line, is chosen by a logic level on the S line of the multiplexer, set by an SW pin routed to the PWM pin of the mikroBUS™ socket.
ISM RX 3 Click possesses the SMA antenna connector with an impedance of 50Ω, which can use it to connect the appropriate antenna that Mikroe has in its offer for improved range and received signal strength.
This Click board™ can be operated only with a 3.3V logic voltage level. The board must perform appropriate logic voltage level conversion before use with MCUs with different logic levels. However, the Click board™ comes equipped with a library containing functions and an example code that can be used, as a reference, for further development
-
Type Sub-1 GHz Transceievers Applications Can be used for home automation and security, building access control, remote keyless entry, garage or gate doors control, and similar applications On-board modules MAX41470 - sub-GHz ISM RF receiver from Maxim Integrated, now part of Analog Devices Key Features Long range with high sensitivity, low power consumption, high performance, self-polling (remote wake-up) for reduced power, gain and frequency control, and more Interface SPI Compatibility mikroBUS Click board size S (28.6 x 25.4 mm) Input Voltage 3.3V